Elk

Plumber and plumbing – some interesting facts


plumbers Wandsworth

Wikipedia about tubes and pipes and how they are different

The difference between pipes and tubes is simply in the way it is sized. PVC pipe for plumbing applications and galvanized steel pipe for instance, are measured in IPS (iron pipe size). Copper tube, CPVC, PeX and other tubing is measured nominally, which is basically an average diameter. These sizing schemes allow for universal adaptation of transitional fittings. For instance, 1/2" PeX tubing is the same size as 1/2" copper tubing. 1/2" PVC on the other hand is not the same size as 1/2" tubing, and therefore requires either a threaded male or female adapter to connect them. When used in agricultural irrigation, the singular form "pipe" is often used as a plural.

Pipe is available in rigid "joints", which come in various lengths depending on the material. Tubing, in particular copper, comes in rigid hard tempered "joints" or soft tempered (annealed) rolls. PeX and CPVC tubing also comes in rigid "joints" or flexible rolls. The temper of the copper, that is whether it is a rigid "joint" or flexible roll, does not affect the sizing.

The thicknesses of the water pipe and tube walls can vary. Pipe wall thickness is denoted by various schedules or for large bore polyethylene pipe in the UK by the Standard Dimension Ratio (SDR), defined as the ratio of the pipe diameter to its wall thickness. Pipe wall thickness increases with schedule, and is available in schedules 20, 40, 80, and higher in special cases. The schedule is largely determined by the operating pressure of the system, with higher pressures commanding greater thickness. Copper tubing is available in four wall thicknesses: type DWV (thinnest wall; only allowed as drain pipe per UPC), type 'M' (thin; typically only allowed as drain pipe by IPC code), type 'L' (thicker, standard duty for water lines and water service), and type 'K' (thickest, typically used underground between the main and the meter). Because piping and tubing are commodities, having a greater wall thickness implies higher initial cost. Thicker walled pipe generally implies greater durability and higher pressure tolerances.

Wall thickness does not affect pipe or tubing size.1/2" L copper has the same outer diameter as 1/2" K or M copper. The same applies to pipe schedules. As a result, a slight increase in pressure losses is realized due to a decrease in flowpath as wall thickness is increased. In other words, 1 foot of 1/2" L copper has slightly less volume than 1 foot of 1/2 M copper.

Źródło: https://en.wikipedia.org/wiki/Plumbing


Common pipe fittings - Tee

A tee is the most common pipe fitting. It is available with all female thread sockets, all solvent weld sockets, or with opposed solvent weld sockets and a side outlet with female threads. It is used to either combine or split a fluid flow. It is a type of pipe fitting which is T-shaped having two outlets, at 90° to the connection to the main line. It is a short piece of pipe with a lateral outlet. A tee is used for connecting pipes of different diameters or for changing the direction of pipe runs. They are made of various materials and available in various sizes and finishes. They are extensively used in pipeline networks to transport two-phase fluid mixtures. They are categorized as:

Equal
Unequal

When the size of the branch is same as header pipes, equal tee is used and when the branch size is less than that of header size, reduced tee will be used. Most common are tees with the same inlet and outlet sizes. Some of the industrial tees are Straight Tee, Reducing Tee, Double Branch Tee, Double Branch Reducing Tee, Conical Tee, Double Branch Conical Tee, Bullhead Tee, Conical Reducing Tee, Double Branch Conical Reducing Tee, Tangential Tee, and Double Branch Tangential Tee.

The above tees are categorized on the basis of their shapes and structure. They can also be classified on the basis of the application they are required to perform.

The three outlet sizes should be named in order (e.g. left, middle, right; measuring 15-22-15). The three sizes of a tee are end x end x center, so a tee that is 1" on both ends and 3/4" in the center it would be 1" x 1" x 3/4".

Źródło: https://en.wikipedia.org/wiki/Piping_and_plumbing_fitting


Wikipedia about valves control

Many valves are controlled manually with a handle attached to the stem. If the handle is turned ninety degrees between operating positions, the valve is called a quarter-turn valve. Butterfly, ball valves, and plug valves are often quarter-turn valves. If the handle is circular with the stem as the axis of rotation in the center of the circle, then the handle is called a handwheel. Valves can also be controlled by actuators attached to the stem. They can be electromechanical actuators such as an electric motor or solenoid, pneumatic actuators which are controlled by air pressure, or hydraulic actuators which are controlled by the pressure of a liquid such as oil or water. Actuators can be used for the purposes of automatic control such as in washing machine cycles, remote control such as the use of a centralised control room, or because manual control is too difficult such as when the valve is very large. Pneumatic actuators and hydraulic actuators need pressurised air or liquid lines to supply the actuator: an inlet line and an outlet line. Pilot valves are valves which are used to control other valves. Pilot valves in the actuator lines control the supply of air or liquid going to the actuators.

The fill valve in a toilet water tank is a liquid level-actuated valve. When a high water level is reached, a mechanism shuts the valve which fills the tank.

In some valve designs, the pressure of the flow fluid itself or pressure difference of the flow fluid between the ports automatically controls flow through the valve.

Źródło: https://en.wikipedia.org/wiki/Valve


Zobacz inne ciekawe wpisy na naszej stronie:


Ćwiczenia i suplementacja aminokwasami

Generalnie aminokwasy sklep to idealne miejsca, aby kupić niezbędne do treningu suplementy i odżywki. Jednak dlaczego dobrze jest uprawiać sport wraz z suplementacją?Żywienie sportowców - WikipediaNadrzędnym zdaniem w planowaniu jadłospisu jest ustalenie równowagi pomiędzy energią przyjmowaną, a wydatkowaną. Utrzymanie tego bilansu jest warunkiem rozwoju fizycznego, zdrowia i aktywności zawodowej człowieka. Odstępstwo od tej równowagi, utrzymujące się w dłuższym czasie moż...

Materiały poligraficzne

Naklejki mogą przybierać rozmaite formy i kształty, w tym również naklejki wypukłe 3d wypełniane tworzywami sztucznymi. O różnych poligraficznych gadżetach.Reklama za pomocą naklejekNaklejki lub jak ktoś woli, nalepki to doskonały materiał marketingowy, który można przykleić na produktach, na witrynie sklepowej lub jak reklama jeżdżąca na samochodach firmowych. Grafik projektując taką naklejkę może puścić wodze fantazji i poszaleć z forma, kształtem i typografią. ...

Zamek do golfa

zamek centralny vw golfGdzie sprzedać uszkodzone auto?Zamiast samochód złomować, można go niby sprzedać. Jednak czy jest etyczne sprzedawanie samochodu, którego nie opłaca się naprawiać? No cóż - w naszym narodzie rzadko mamy takie dylematy - niestety. Jeżeli wystawimy samochód tanio, dokładnie opisując jego stan techniczny i znajdzie się kupiec - to problemu nie ma, postępujemy uczciwie. Jednak jeżeli zamierzamy oszukać kogoś i sprzedać samochód w złym stanie technicz...

Tradycje i zwyczaje pogrzebowe

ceremonie pogrzebowe sopotJak przeprowadzić pogrzeb?Aby dobrze zorganizować pogrzeb, na początku należy poczytać co nieco o kwestiach formalnych, które koniecznie trzeba wypełnić. Zwykle na załatwienie ich wszystkich mamy jedynie kilka dni, dlatego warto będzie wszystko spisać i zaplanować poszczególne kwestie bardzo dokładnie. Jeśli chcemy, by całość była wykonana bez żadnych problemów, musimy oczywiście do sprawy podchodzić sumiennie, a dzięki temu będziemy mieć pewno...